#Blood bag typ o portable#
#Blood bag typ o free#

Do not dispose the AGELESS packet with wastes containing volatile or flammable materials.ĥ.14. Dispose of the AGELESS packet with the blister tray.ĥ.13. Do not open and handle it with care.ĥ.12. The AGELESS® (oxygen absorber packet, Mitsubishi Gas Chemical) contained in this package absorbs oxygen and generates heat on removal. Discard phlebotomy needle/donor tubing according to institutional standard operating procedures.ĥ.11. Do not touch needle after removing the needle cover.ĥ.10. Do not use a dielectric tube sealer to seal the tubing while the needle is connected to the donor's body unless it is approved for such a purpose.ĥ.9. If the amount of moisture is greater than expected, check for leaks from the fluid-filled components of the blood bag set.ĥ.8. It is normal to have condensation in the blister packaging. Recommended storage conditions: Room Temperature (15-30☌/59-86☏).ĥ.6. Avoid excessive heat and direct sunlight. Always inspect the blood bag set for leaks before use.ĥ.4.

#Blood bag typ o free#

Do not use unless solutions are clear and free from particulates.ĥ.3. NOTE: Production of Platelets and Plasma is not intended with this product.ĥ.2. For further preparation and processing of other components, use standard processing and storage techniques following approved regulations and standards.Ģ.17.1. Store CPDA-1 Whole Blood (or Red Blood Cells) between 1 – 6 ° C for up to 35 days.Ģ.17. Leave segments attached to Whole Blood unit.Ģ.16. Make an appropriate number of segments of anticoagulated blood for testing by sealing on or near the X marks. To prevent the blood from clotting in the tubing, work quickly as possible. Strip blood from donor tubing into collection bag, mix well, and allow tubing to refill repeat once. Immediately after collection, invert collection bag several times to assure blood and anticoagulant are well mixed.Ģ.15. CAUTION: Discard phlebotomy needle/donor tubing according to institutional standard operating procedures.Ģ.14. If using a needle safety device, follow manufacturer's instructions.Ģ.13.1. Reapply clamp to donor tubing release pressure on donor's arm and remove needle. CAUTION: Do not use a dielectric tube sealer to seal the tubing while the needle is connected to the donor's body unless it is approved for such a purpose.Ģ.13. Collect blood samples using careful attention to aseptic technique and following your institution's standard operating procedures.Ģ.12.1. Alternate methods may be used to seal tubing. Sever donor tubing between knot and clamp. Temporarily clamp between the knot and needle. When the desired amount of blood has been collected, seal the tubing or tighten the loose knot (white knot) prepared in Step 2.3. Collect labeled volume of blood 250 mL ☑0%.Ģ.12. If using an automated mixer, follow manufacturer's instructions.Ģ.11. Mix blood with anticoagulant in the collection bag and continue to mix at several intervals during collection and immediately after collection. Remove the temporary clamp on the donor tubing to permit blood flow into the collection bag.Ģ.10. CAUTION: Do not touch the needle after removing the needle cover.Ģ.8. Remove the needle cover and perform phlebotomy.Ģ.7.1.

If blood pressure cuff is used, inflate to approximately 60 mmHg.Ģ.7. Disinfect site of phlebotomy according to institutional standard operating procedures. Apply blood pressure cuff or tourniquet to donor's arm. Suspend the collection bag as far as possible below the donor's arm.Ģ.6. Make a loose knot in the donor tubing approximately 10 cm or 4 inches from the needle unless alternate methods are used to seal the tubing at the end of collection.Ģ.5. Prepare the blood bag following your institution's standard operating procedures.Ģ.3. To open blister package, peel cover film back 4/5 of its length.Ģ.2. Simulated IV fluids typically have a one (1) year shelf life.2.1. *Printed expiration date is strictly for simulation purposes. SimRx Stainless Blood Bags are recommended if simulated blood must be infused into manikins. This solution is not intended for infusion into manikins as damage to the tubing system may result. SimRx Simulated Blood Bags are made from a proprietary formula that contains sugar solids and red dye for realism.

450mL bags filled with 300mL of simulated blood.

Available in all 8 blood types: A+, A-, B+, B-, AB+, AB-, O+, O.

*Simulated Blood Bags Are For Instructional Use Only. SimRx Simulated Blood Products are available in all eight A/B/O blood types and come with bar-coded patient identification labels. SimRx Simulated Blood Bags realistically replicate units of packed red blood cells in order to teach blood transfusion procedures. They are filled with lifelike fluid that is realistic in color and texture.

On-Site Repairs & Preventive Maintenance.

#Blood bag typ o portable#

Backdrops & Portable Display Surroundings.